Hou Jie
,
Gao Huichang
,
Wang Yingjun
,
Cheng Delin
,
Cao Xiaodong
材料科学技术（英）
doi:10.1016/j.jmst.2016.08.013
Modifying substrates through mineralization is a popular way to improve the osteogenic performance. Screening of the best mineralization characteristics on specific substrates for stem cells is meaningful but not fully studied. In this paper, poly(lactic-co-glycolic acid)/hydroxyapatite (PLGA/HA, PH) microsphere scaffolds with superficial pores were fabricated by a low-temperature fusion method. After the mineralization in the 5× stimulated body fluid (SBF) for 0, 7, 12 and 24?h, four mineralized scaffolds (MPH-0, MPH-7, MPH-12 and MPH-24) with different apatite topographies were obtained. It was found that the surface of MPH-7 was evenly decorated with abundant micro-pores, MPH-12 with dense and plain apatite layer, and MPH-24 with small spherical bumps. The responses of mouse bone mesenchymal stem cells (mBMSCs) to the four scaffolds were further studied. The results showed that MPH-7 and MPH-24 had more obvious effects on mBMSCs attachment, proliferation and differentiation than MPH-0 and MPH-12. This work indicated that to obtain the maximum improvement, the mineralization characteristics had to be carefully chosen. This was noteworthy in the chemical modification of surfaces to form the functionalized scaffolds for bone repair.
关键词:
Microsphere scaffold
,
Mineralization
,
Topography
,
Cell behavior
Nuclear Engineering and Design
Liquid droplet erosion (LDE), which often occurs in bellows made of nickel-based alloys, threatens the security operation of the nuclear power plant. As the candidate materials of the bellows, Inconel 600 and Inconel 625 were both tested for resistance to cavitation erosion (CE) and jet impingement erosion (JIE) through vibratory cavitation equipment and a jet apparatus for erosion-corrosion. Cumulative mass loss vs. exposure time was used to evaluate the erosion rate of the two alloys. The surface and cross-sectional morphologies before and after the erosion tests were observed by scanning electron microscopy (SEM), the inclusions were analyzed by an energy dispersive spectroscopy (EDS), and the surface roughness was also measured by surface roughness tester to illustrate the evolution of erosion process. The results show that the cumulative mass loss of CE of Inconel 625 is about 1/6 that of Inconel 600 and the CE incubation period of the Inconel 625 is 4 times as long as that of the Inconel 600. The micro-morphology evolution of CE process illustrates that the twinning and hardness of the Inconel 625 plays a significant role in CE. In addition, the cumulative mass loss of JIE of Inconel 625 is about 2/3 that of Inconel 600 at impacting angle of 90 degrees, and almost equal to that of the Inconel 600 at impacting angle of 30 degrees. Overall, the resistance to CE and JIE of Inconel 625 is much superior to that of Inconel 600. (C) 2010 Elsevier By. All rights reserved.
关键词:
stress-corrosion cracking;aluminide intermetallic alloys;high-purity;water;mechanical-properties;crevice corrosion;solid particles;wear;behavior;microstructure;deformation;steam
Scripta Materialia
A recent comment on a previously published paper addressed the invalid explanation of the off diagonal interdiflusion coefficients of the beta-Ni(Al,Cr) phase in the Ni-Cr-Al system according to the symmetric property of the thermodynamic matrix. In this paper, the experimental data presented by Hou et al. was reanalyzed and the interdiffusion coefficient matrix was estimated again. The results of the analysis have been discussed in terms of a brief reply to the comments of Liu and Liang. (C) 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
关键词:
Diffusion;Intermetallic compound;Ni-Cr-Al
Nuclear Engineering and Design
A composite coating was deposited on Inconel 600 substrate by cold spray method using pure Ni powder (60 wt.%) blended with alpha-Al(2)O(3) (40 wt.%) as feedstock. It is expected to be applied to repair the bellows eroded by the liquid droplet erosion (LDE). Microstructure of the coating was observed using optical microscope (OM) and scanning electron microscopy (SEM). Microhardness of the coating was determined by Vickers hardness tester. Cavitation erosion (CE) experiments were carried out in the distilled water. Jet impingement erosion (JIE) experiments were performed in slurry containing 1 wt.% quartz particle with the flow velocity of 15 m/s at impingement angles of 30 degrees, 60 degrees and 90 degrees, respectively. Cumulative mass loss vs. testing time was used to evaluate the erosion rate of the coating. The erosion mechanism was analyzed by OM, SEM, X-ray diffraction (XRD) and the microhardness measurement. The results show that the composite coating has compact microstructure and relatively high hardness. The resistance to CE of the coating is not as good as that of Inconel 600 substrate due to the weak bonds of the Al(2)O(3) particles. However, the results of the JIE test indicate that the slurry erosion resistance of the coating is better than that of Inconel 600 at the impact angles of 30 degrees and 60 degrees, but not at the normal impact angle. (C) 2011 Elsevier B.V. All rights reserved.
关键词:
large powder particles;composite coatings;slurry erosion;kinetic;spray;liquid impact;alloy;microstructure;steels;deposition;resistance
张春路
,
丁国良
,
李灏
工程热物理学报
准确、快速、稳定地计算制冷剂热力性质是计算机辅助设计和工程计算的
要求。本文将隐式拟合方法与MartinHou方程相结合，提出制冷剂过热气体热力
性质的隐式拟合方法，该方法不仅具有形式统一、精度高、速度快、外推性和
稳定性好的优点，而且保证了过热区与两相区之间热力性质的连续性
关键词:
制冷剂
,
过热气体
,
热力性质
,
拟合
涂娜
,
江向平
,
李小红
,
傅小龙
,
杨帆
人工晶体学报
采用传统固相法制备了(1-x)Bi4Ti3 O12-xSrBi2 Nb2 O9(BIT-SBN,x=0,0.025,0.050,0.100,0.150,0.200)铋层状无铅压电陶瓷.系统研究了SrBi2 Nb2 O9掺杂对Bi4Ti3 O12基陶瓷物相结构、微观结构以及jie电性能的影响.结果表明:所有陶瓷样品均为单一的铋层状结构;当SBN掺量为0.100时,样品具有最佳的电性能:d33=21 pC/N,相对密度ρ =98.1％,机电耦合系数kp=8.26％,εr=220,介电损耗tanδ =0.29％,剩余极化强度Pr=9.128 μC/cm2,Tc=594℃.同时,SBN的引入增强了样品的抗老化性和热稳定性.
关键词:
Bi4Ti3O12
,
SrBi2Nb2O9
,
铋层状
,
铁电陶瓷
,
介电性能
曾东
,
燕瑛
,
王立朋
,
刘兵山
复合材料学报
doi:10.3321/j.issn:1000-3851.2005.06.022
通过三维动力学有限元法,采用空间杆单元来描述缝线,结合试验系统地研究了缝合复合材料的低速冲击损伤问题.采用修正的赫兹接触定律计算冲击接触力,NewMark直接积分法求解运动方程,求解冲击过程中的应力应变;在Chang和Hou等的分层扩展准则基础上,提出一修正的分层扩展准则并考虑纤维断裂,建立了分析低速冲击损伤面积的方法;对相同铺层的缝合与未缝合复合材料层板进行了低速冲击试验.分析结果与实验结果具有良好的一致性,证明本文中提出的修正的分层扩展准则是正确的.计算及试验结果均表明,在相同冲击能量作用下,缝合使冲击损伤面积明显减小.
关键词:
缝合复合材料
,
低速冲击
,
三维有限元
,
损伤面积
